Notice on Mixed Container Loading of Drumed Goods

Dear customers,
From now on, pentane, hexane and heptane can be mixed to be loaded into one container for shipment. The premise is that as long as the Bill of lading merchant shows the same consignee, the same shipper and the shipping company accepts it, shipment can be made. In other words, each product is no longer limited by the minimum packing quantity of a whole container load.

The following points shall be achieved for container mixed loading:
1、 Goods of different shapes and packages should not be packed together. It is easy to get confused.
2、 If the goods will exude dust, liquid, etc. from the packaging, they should not be placed together with other goods to avoid pollution. If they must be placed together, they should be isolated, such as using canvas or plastic film.
3、 How to put the goods of different weights? Put the light one on top of the heavy one.
4、 How to put the goods with different packing degrees? Put the strong one at the bottom and the light one at the top.
5、 If there are liquid and clean goods, it is better to put them under other goods.
6、 If there are goods with sharp corners or protruding parts in the goods, they need to be covered with something, otherwise other goods will be damaged.

Attention shall be paid to when loading sea containers

1. When the packing rate reaches 90%, it is necessary to be more cautious in packing.
2. After the container is towed, you should first check it, take the container paper to check the box number, take good care of the lead seal given to you by the driver, and write down the lead seal number.
3. In any case, when the goods are loaded into the container, the weight of the goods in the container shall not exceed the large loading capacity of the container, that is, the total amount of the container minus the dead weight of the container. Generally, the total weight and dead weight will be marked on the door of the container.
4. The unit volume weight of each container is specific, so when the same kind of goods are loaded in the container, as long as the density of the goods is known, it can be determined whether it is heavy or light.
5. During loading, the load on the bottom of the box shall be balanced, especially when the center of gravity of the load deviates from one end.
6. Avoid concentrated load. For example, when loading heavy goods such as mechanical equipment, the bottom of the box shall be paved with wood and other cushion materials to disperse the load as much as possible.
7. When using manual loading, pay attention to whether there are loading and unloading instructions such as “do not put upside down”, “place horizontally”, “place vertically” on the package. Be sure to use the loading tools correctly. It is forbidden to use the hand hook for baling. The goods in the box shall be loaded neatly and stacked tightly. For goods that are easy to be bundled loose and packed fragile, a pad or plywood shall be inserted between the goods to prevent the goods from moving in the box.
8. When loading pallet goods, it is necessary to accurately master the internal dimensions of the container and the external dimensions of the goods package, so as to calculate the number of loaded pieces, so as to minimize the number of abandoned places and load more goods.
9. When calculating the loading scheme, remember that there is an angle iron protruding from the upper left / right corner of the shipping container, leaving about 10x10x15cm space.
10. Cartons are not standard parts. Before loading, actually measure the size, not just based on the original data of the carton factory. In many cases, the middle of the cartons filled with goods will be slightly raised than the side. Therefore, it is prudent to keep a gap of about two centimeters around the inner periphery of the container during calculation.
11. Cartons are elastic and will be naturally dense after stacking. Before loading, first communicate with the loading and unloading foreman to let him roughly understand the loading scheme. But we must not slacken off. When doing physical work, people are not able to use their brains clearly, so they should pay attention to supervision nearby.
12. When the forklift truck is used for packing, it will be limited by the free lifting height of the machinery and the height of the gantry. Therefore, if conditions permit, the forklift can load two layers at a time, but there should be a specific gap between the top and bottom.
13. Generally, fork lift trucks with a common lifting capacity of 2 tons are used, and their free lifting height is about 1250px. However, there is also a forklift truck with full free lifting height. As long as the height of the box allows, this machine is not affected by the lifting height of the gantry, and can easily stack two layers of goods. In addition, it should also be noted that the skid should be laid under the goods so that the fork can be pulled out smoothly.
14. The goods should not be packed naked. At least they should be packed. Do not blindly damage the goods to save space. General goods will also be packed.